Waterborne sealer Does not require thinning under normal environmental and application conditions (65°-75°,40-60% relative humidity) Non-photochemically reactive For use over newly sanded or stained sport floors

---

FEATURES:

• Formulated for use with Pacific Sport Finishes by BonaKemi
• Seals the wood, preventing the finish from penetrating, thus keeping more finish on top of the wood
• Minimizes sidebonding
• Non-yellowing
• VOC compliant
• Fast drying
• Virtually odorless
• Nonflammable
• Water clean-up

---

RECOMMENDED USES:

• Basketball courts
• Volleyball courts
• Racquetball and squash courts
• Badminton courts
• Multi-purpose gym and stage floors
• Aerobic and dance floors

---

DIRECTIONS FOR USE:

NOTE: THE USE OF PACIFIC SPORT SEAL MINIMIZES THE POSSIBILITY OF SIDEBONDING. SPORT SEAL is compatible with most hardwood floor finishes after proper preparation and dry times. ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY.

PREPARATION:

SANDING AND FINISHING NEW FLOORS

1. Sand floor using MFMA accepted methods. 2. Make your final cut with 100-120 grit paper. Screen with 120-150 grit screen. This burnishing will reduce the amount of grain raise. 3. Vacuum thoroughly. 4. Tack with slightly water-dampened cloth. 5. Apply sealer and finish system (see finish directions).

NOTE: PACIFIC SPORT SEAL/FINISH SYSTEM IS A 4-COAT SYSTEM:

• 1 coat PACIFIC SPORT SEAL
• 3 coats PACIFIC SPORT FINISHES

NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.

SEALING: SHAKE WELL BEFORE USING. 1. Using a plastic pour can, pour a 4" wide line of PACIFIC SPORT SEAL along the starting wall. Go with the grain of the wood. 2. Using a clean, pre-dampened applicator, draw the applicator forward, with the grain of the wood, moving PACIFIC SPORT SEAL toward the opposite wall. By holding the applicator at a "snowplow" angle, it maintains a wet edge at all times. 3. At the end of each stroke, turn the applicator toward you and pad out the applicator parallel to the wet edge. 4. Feather all turns. If pushed too hard or too fast, drips will fly off the applicator. 5. Missed areas can be touched up if seen right away. 6. To prevent lapping and dry marks, be sure you are using the recommended coverage. Be careful not to spread PACIFIC SPORT SEAL too thin. Your coverage should be approximately 500-600 sq. ft. per gallon. 7. Allow PACIFIC SPORT SEAL to dry 1-2 hours before applying a Pacific Sport Waterborne Finish.

INTERCOAT ABRASION: Abrading between coats is not necessary for adhesion. However, for smoothest floor results, buff the sealer coat with a Bona CPS4000 Sealer Pad. NOTE: Vacuum and tack thoroughly before applying first coat of finish and game lines. Apply 1 coat of finish before painting game lines. Game lines should be painted using an acrylic latex flat enamel. Do not use paints containing vinyls or poly-vinyls. ALWAYS PREPARE A TEST OR SAMPLE AREA TO DETERMINE COMPATIBILITY AND ADHESION.

CLEAN-UP: Tools should be cleaned with water and stored in the BonaKemi Applicator Storage Canister.

---

SPECIFICATIONS/PHYSICAL DATA:

Ingredients - Acrylic polymer dispersion in water
Color - Milky white (wet)
Odor - Non-offending
Clarity - Clear when dry
Solids - 32%
pH - 3.9
Viscosity - (#4 Ford cup @ 25C) 13 seconds
Flash Point - >200° F
Density - 8.70 lbs./gallon (1.04 S.G.)
Stability - 1 year shelf life
Leveling - Excellent
Defoaming - Excellent
Drying Time - 1 - 2 hours
Percent Cured After 24 Hours - 70%
Maximum Cure - 100% after one week
Gloss Level - N/A
Coverage - 500-600 sq. ft./gallon
VOC - Does not exceed 250 grams per liter (2.1 lbs. per gallon)
Application Tools - Bona brush, foam backed applicator, Swedish roller

---

PACKAGING:

• 1 gallon plastic bottle
• 5 gallon plastic pail